View BGA2715_1219337.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

BGA2715
MMIC wideband amplifier
Rev. 02 -- 24 September 2004 Product data sheet
1. Product profile
1.1 General description
Silicon Monolithic Microwave Integrated Circuit (MMIC) wideband amplifier with internal matching circuit in a 6-pin SOT363 SMD plastic package.
CAUTION This device is sensitive to electrostatic discharge (ESD). Therefore care should be taken during transport and handling.
MSC895
1.2 Features
s s s s s s s Internally matched to 50 Wide frequency range (3.3 GHz at 3 dB bandwidth) Flat 22 dB gain (1 dB up to 2.8 GHz) -8 dBm output power at 1dB compression point Good linearity for low current (IP3out = 2 dBm) Low second harmonic, -30 dBc at PD = -40 dBm Unconditionally stable (K 2).
1.3 Applications
s s s s LNB IF amplifiers Cable systems ISM General purpose.
1.4 Quick reference data
Table 1: Symbol VS IS s21 NF PL(sat) 2 Quick reference data Parameter DC supply voltage supply current insertion power gain noise figure saturated load power f = 1 GHz f = 1 GHz f = 1 GHz Conditions Min Typ 5 4.3 22 2.6 -4 Max 6 Unit V mA dB dB dBm
Philips Semiconductors
BGA2715
MMIC wideband amplifier
2. Pinning information
Table 2: Pin 1 2, 5 3 4 6 Pinning Description VS GND2 RF_OUT GND1 RF_IN
1 2 3
SOT363
Simplified outline
6 5 4
Symbol
1 6 4 2, 5
sym052
3
3. Ordering information
Table 3: Ordering information Package Name BGA2715 Description plastic surface mounted package; 6 leads Version SOT363 Type number
4. Marking
Table 4: BGA2715 Marking Marking code B6Type number
5. Limiting values
Table 5: Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Symbol VS IS Ptot Tstg Tj PD Parameter DC supply voltage supply current total power dissipation storage temperature junction temperature maximum drive power Tsp 90 C Conditions RF input AC coupled Min -65 Max 6 8 200 +150 150 -10 Unit V mA mW C C dBm
9397 750 13291
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 02 -- 24 September 2004
2 of 14
Philips Semiconductors
BGA2715
MMIC wideband amplifier
6. Thermal characteristics
Table 6: Symbol Rth(j-sp) Thermal characteristics Parameter thermal resistance from junction to solder point Conditions Ptot = 200 mW; Tsp 90 C Typ 300 Unit K/W
7. Characteristics
Table 7: Characteristics VS = 5 V; IS = 4.3 mA; Tj = 25 C; measured on demo board; unless otherwise specified. Symbol Parameter IS s21 2 supply current insertion power gain f = 100 MHz f = 1 GHz f = 1.8 GHz f = 2.2 GHz f = 2.6 GHz f = 3 GHz s112 s22 2 input return losses output return losses isolation noise figure bandwidth stability factor saturated load power load power f = 1 GHz f = 2.2 GHz f = 1 GHz f = 2.2 GHz s122 NF B K PL(sat) PL(1dB) f = 1.6 GHz f = 2.2 GHz f = 1 GHz f = 2.2 GHz at s212 -3 dB below flat gain at 1 GHz f = 1 GHz f = 2.2 GHz f = 1 GHz f = 2.2 GHz at 1 dB gain compression; f = 1 GHz at 1 dB gain compression; f = 2.2 GHz IM2 second order intermodulation product input, third order intercept point output, third order intercept point at PD = -40 dBm, f0 = 1 GHz Conditions Min 3.5 11 20 21 21 20 18 10 8 10 7 53 38 3 -5 -6 -9 -10 29 Typ 4.3 13.3 21.7 23.2 23.3 22.1 20.1 12 10 12 8.5 54 39 2.6 3.1 3.3 18 2.3 -4.0 -5.0 -8.0 -8.5 30 Max Unit 5.5 15 23 25 25 24 22 2.8 3.3 dBm dBm dBm dBm dBc mA dB dB dB dB dB dB dB dB dB dB dB dB dB dB GHz
IP3in IP3out
f = 1 GHz f = 2.2 GHz f = 1 GHz f = 2.2 GHz
-21 -24 0 -1
-19.4 -22.7 2.3 0.6
-
dBm dBm dBm dBm
9397 750 13291
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 02 -- 24 September 2004
3 of 14
Philips Semiconductors
BGA2715
MMIC wideband amplifier
8. Application information
Figure 1 shows a typical application circuit for the BGA2715 MMIC. The device is internally matched to 50 , and therefore does not need any external matching. The value of the input and output DC blocking capacitors C2 and C3 should not be more than 100 pF for applications above 100 MHz. However, when the device is operated below 100 MHz, the capacitor value should be increased. The 22 nF supply decoupling capacitor, C1 should be located as close as possible to the MMIC. The printed-circuit board (PCB) top ground plane, connected to pins 2, 4 and 5 must be as close as possible to the MMIC, and ideally directly beneath it. When using via holes, use multiple via holes, located as close as possible to the MMIC.
VS
C1
1 VS
C2
RF input
6 RF_IN
RF_OUT 3
C3
RF output
GND1
GND2
4
2, 5
mgu435
Fig 1. Typical application circuit.
Figure 2 shows the PCB layout, used for the standard demonstration board.
9397 750 13291
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 02 -- 24 September 2004
4 of 14
Philips Semiconductors
BGA2715
MMIC wideband amplifier
30 mm
PH
30 mm
PHILIPS
IN
OUT
V+
PH
DUT C2 C3
PHILIPS
IN
C1
OUT
V+
001aab255
Material = FR4, thickness = 0.6 mm, r = 4.6.
Fig 2. PCB layout and demonstration board showing components.
8.1 Grounding and output impedance
If the grounding is not optimal, the gain becomes less flat and the 50 output matching becomes worse. To further increase output matching to 50 , a 12 resistor (R1) can be placed in series with C3 (see Figure 3). This will significantly improve the output impedance, at the cost of 1 dB gain and 1 dB output power.
9397 750 13291 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 02 -- 24 September 2004
5 of 14
Philips Semiconductors
BGA2715
MMIC wideband amplifier
VS
C1
VS
C2
RF input
RF_IN
RF_OUT
C3
R1
RF output
GND1
GND2
001aab346
Fig 3. Application circuit for better output impedance into 50 .
8.2 Application examples
The excellent wideband characteristics of the MMIC make it an ideal building block in IF amplifiers such as LNBs (see Figure 4). As second amplifier after an LNA, the MMIC offers an easy matching, low noise solution (see Figure 5).
mixer from RF circuit wideband amplifier oscillator
mgu438
to IF circuit or demodulator
Fig 4. Application as IF amplifier.
mixer antenna LNA wideband amplifier oscillator
mgu439
to IF circuit or demodulator
Fig 5. Application as RF amplifier.
9397 750 13291
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 02 -- 24 September 2004
6 of 14
Philips Semiconductors
BGA2715
MMIC wideband amplifier
90 +1 135 +0.5 +2 45 1.0 0.8 0.6 +0.2 4 GHz 0 0.2 0.5 100 MHz 1 2 5 10 0.4 0.2 0 0
+5
180
-0.2
-5
-135
-0.5 -1 -90
-2
-45 1.0
001aab247
IS = 4.3 mA; VS = 5 V; PD = -35 dBm; Zo = 50 .
Fig 6. Input reflection coefficient (s11); typical values.
90 +1 135 +0.5 +2 45 1.0 0.8 0.6 +0.2 0.4 0.2 180 0 0.2 0.5 1 4 GHz -0.2 -5 2 100 MHz 5 10 0 0
+5
-135
-0.5 -1 -90
-2
-45 1.0
001aab248
IS = 4.3 mA; VS = 5 V; PD = -35 dBm; Zo = 50 .
Fig 7. Output reflection coefficient (s22); typical values.
9397 750 13291
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 02 -- 24 September 2004
7 of 14
Philips Semiconductors
BGA2715
MMIC wideband amplifier
0 |s12 | 2 (dB) -20
001aab249
30 |s21| 2 (dB) 20
001aab250
(1) (2) (3)
-40
10
-60 0 1000 2000 3000 f (MHz) 4000
0 0 1000 2000 3000 f (MHz) 4000
IS = 4.3 mA; VS = 5 V; PD = -35 dBm; Zo = 50 .
PD = -35 dBm; Zo = 50 . (1) IS = 4.7 mA; VS = 5.5 V. (2) IS = 4.3 mA; VS = 5 V. (3) IS = 3.9 mA; VS = 4.5 V.
Fig 8. Isolation typical values.
0 PL (dBm)
(s122)
as a function of frequency;
Fig 9. Insertion gain (s212) as a function of frequency; typical values.
0 PL (dBm)
001aab252
001aab251
(1) (2) (3)
(1) (2) (3)
-10
-10
-20
-20
-30 -50
-40
-30
-20
-10 PD (dBm)
-30 -50
-40
-30
-20
-10 PD (dBm)
f = 1 GHz; Zo = 50 . (1) VS = 5.5 V. (2) VS = 5 V. (3) VS = 4.5 V.
f = 2.2 GHz; Zo = 50 . (1) VS = 5.5 V. (2) VS = 5 V. (3) VS = 4.5 V.
Fig 10. Load power as a function of drive power at 1 GHz; typical values.
Fig 11. Load power as a function of drive power at 2.2 GHz; typical values.
9397 750 13291
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 02 -- 24 September 2004
8 of 14
Philips Semiconductors
BGA2715
MMIC wideband amplifier
5 NF (dB) 4
001aab253
40 K 30
001aab254
(3)
3
(2) (1)
20
2
10 1
0 0 500 1000 1500 2000 2500 f (MHz)
0 0 1000 2000 3000 f (MHz) 4000
Zo = 50 . (1) IS = 4.7 mA; VS = 5.5 V. (2) IS = 4.3 mA; VS = 5 V. (3) IS = 3.9 mA; VS = 4.5 V.
IS = 4.3 mA; VS = 5 V; Zo = 50 .
Fig 12. Noise figure as a function of frequency; typical values.
Fig 13. Stability factor as a function of frequency; typical values.
9397 750 13291
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 02 -- 24 September 2004
9 of 14
Philips Semiconductors
BGA2715
MMIC wideband amplifier
Table 8: Scattering parameters VS = 5 V; IS = 4.3 mA; PD = -35 dBm; Zo = 50 ; Tamb = 25 C. f (MHz) 100 200 400 600 800 1000 1200 1400 1600 1800 2000 2200 2400 2600 2800 3000 3200 3400 3600 3800 4000 s11 Magnitude (ratio) 0.100503 0.121228 0.217855 0.26219 0.26297 0.241089 0.211289 0.18828 0.187898 0.231527 0.257172 0.303945 0.311735 0.288113 0.265404 0.24479 0.225353 0.219366 0.226203 0.23349 0.244216 Angle (deg) 27.76918 24.6812 3.974108 s21 Magnitude (ratio) 4.641604 5.427784 7.924499 Angle (deg) 13.82793 7.997073 s12 Magnitude Angle (ratio) (deg) 0.01958 0.003611 -110.345 -114.8849 -77.39562 -170.6765 124.9044 155.3396 147.5162 138.7051 124.9325 120.4153 103.0426 94.4722 54.07247 33.11605 7.697541 -11.0858 -28.17932 -45.60266 -60.69421 -72.89823 -85.18773 s22 Magnitude (ratio) 0.231889 0.219504 0.223868 0.22656 0.237554 0.25378 0.271479 0.287623 0.307361 0.338893 0.352132 0.378963 0.359508 0.349807 0.327615 0.296875 0.27147 0.247253 0.217973 0.184766 0.150082 Angle (deg) Kfactor
-14.37137 5.2 -14.09179 23.9 -23.69087 33.8 -34.95361 33.8 -48.11004 26.8 -63.76927 17.8 -82.31896 12.2 -104.1092 8.4 -125.9161 6.7 -154.6072 5.1 177.7152 145.8774 115.0129 88.0727 61.52393 39.00544 18.63863 3.2 2.3 2.0 1.9 2.3 2.3 2.8
-7.594877 0.001688 -30.92853 0.001336 -55.31486 0.001473 -80.09316 0.002036 -104.2842 0.002785 -128.89 -179.671 154.6647 127.2237 100.012 74.12332 48.40486 25.3978 3.789364 0.003866 0.005641 0.008743 0.011662 0.014471 0.017402 0.016703 0.019651 0.018743 -153.3766 0.004588
-28.08926 9.807075 -61.21535 11.13563 -96.9469 175.4377 128.6387 80.79592 40.08414 2.249913 12.17817 13.60797 14.14423 14.54321 14.65137 14.61385 -136.4953 13.02575
-39.67469 13.78165 -77.37179 12.75107 -114.1115 11.55715 -151.8463 10.12992 170.8795 136.6841 106.1421 78.62692 54.63669 8.961976 8.061087 7.318683 6.619309 6.105669
-16.85382 0.019073 -37.20896 0.019248 -56.90074 0.020895 -75.98154 0.020531
-1.617895 3.0 -21.22008 3.3 -40.71164 3.4 -60.81328 3.8
9397 750 13291
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 02 -- 24 September 2004
10 of 14
Philips Semiconductors
BGA2715
MMIC wideband amplifier
9. Package outline
Plastic surface mounted package; 6 leads SOT363
D
B
E
A
X
y
HE
vMA
6
5
4
Q
pin 1 index
A
A1
1
e1 e
2
bp
3
wM B detail X Lp
c
0
1 scale
2 mm
DIMENSIONS (mm are the original dimensions) UNIT mm A 1.1 0.8 A1 max 0.1 bp 0.30 0.20 c 0.25 0.10 D 2.2 1.8 E 1.35 1.15 e 1.3 e1 0.65 HE 2.2 2.0 Lp 0.45 0.15 Q 0.25 0.15 v 0.2 w 0.2 y 0.1
OUTLINE VERSION SOT363
REFERENCES IEC JEDEC EIAJ SC-88
EUROPEAN PROJECTION
ISSUE DATE 97-02-28
Fig 14. Package outline; SOT363 (SC-88).
9397 750 13291 (c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 02 -- 24 September 2004
11 of 14
Philips Semiconductors
BGA2715
MMIC wideband amplifier
10. Revision history
Table 9: Revision history Release date 20040924 Data sheet status Product data sheet Change notice Doc. number 9397 750 13291 Supersedes BGA2715_N_1 Document ID BGA2715_2 Modifications: BGA2715_N_1
*
The format of this data sheet has been redesigned to comply with the new presentation and information standard of Philips Semiconductors Preliminary data sheet 9397 750 12826 -
20040202
9397 750 13291
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 02 -- 24 September 2004
12 of 14
Philips Semiconductors
BGA2715
MMIC wideband amplifier
11. Data sheet status
Level I II Data sheet status [1] Objective data Preliminary data Product status [2] [3] Development Qualification Definition This data sheet contains data from the objective specification for product development. Philips Semiconductors reserves the right to change the specification in any manner without notice. This data sheet contains data from the preliminary specification. Supplementary data will be published at a later date. Philips Semiconductors reserves the right to change the specification without notice, in order to improve the design and supply the best possible product. This data sheet contains data from the product specification. Philips Semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. Relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN).
III
Product data
Production
[1] [2] [3]
Please consult the most recently issued data sheet before initiating or completing a design. The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com. For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status.
12. Definitions
Short-form specification -- The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition -- Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information -- Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification.
13. Disclaimers
Life support -- These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes -- Philips Semiconductors reserves the right to make changes in the products - including circuits, standard cells, and/or software - described or contained herein in order to improve design and/or performance. When the product is in full production (status `Production'), relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified.
14. Contact information
For additional information, please visit: http://www.semiconductors.philips.com For sales office addresses, send an email to: sales.addresses@www.semiconductors.philips.com
9397 750 13291
(c) Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Product data sheet
Rev. 02 -- 24 September 2004
13 of 14
Philips Semiconductors
BGA2715
MMIC wideband amplifier
15. Contents
11 1.1 1.2 1.3 1.4 2 3 4 5 6 7 8 8.1 8.2 9 10 11 12 13 14 Product profile . . . . . . . . . . . . . . . . . . . . . . . . . . 1 General description. . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Quick reference data. . . . . . . . . . . . . . . . . . . . . 1 Pinning information . . . . . . . . . . . . . . . . . . . . . . 2 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 2 Thermal characteristics. . . . . . . . . . . . . . . . . . . 3 Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Application information. . . . . . . . . . . . . . . . . . . 4 Grounding and output impedance . . . . . . . . . . 5 Application examples . . . . . . . . . . . . . . . . . . . . 6 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 11 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 12 Data sheet status . . . . . . . . . . . . . . . . . . . . . . . 13 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Contact information . . . . . . . . . . . . . . . . . . . . 13
(c) Koninklijke Philips Electronics N.V. 2004
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. Date of release: 24 September 2004 Document number: 9397 750 13291
Published in The Netherlands

▲Up To Search▲

Price & Availability of BGA2715

	To Download BGA2715 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .